Development of technical means for designing technological and machine equipment for frame layout

Authors

  • D. A. Dmitriev Kherson National Technical University, Ukraine
  • S. A. Rusanov Kherson National Technical University, Ukraine
  • A. A. Omelchuk Kherson National Technical University, Ukraine
  • D. D. Fedorchuk Kherson National Technical University, Ukraine

DOI:

https://doi.org/10.20535/2521-1943.2017.81.112783

Keywords:

technical design tools, surface treatment strategies, frame-based spatial layouts, glide equipment

Abstract

The article analyzes the strategies for processing surfaces of the second order with the smallest deviation from the planned trajectories. The analysis of the behavior of glide equipment is applied to the use of standard processing strategies in the line of authoring software products, such as Tools Glide and Tools Response. The possibility of choosing second-order surface treatment strategies based on the calculated accuracy criteria is shown. Preliminary recommendations on the location of typical trajectories along the z coordinate in the working space of the machine tool are obtained. It is established that the layout with inclined guides greatly increases the rigidity of the arrangement as compared to the parallel guides. Based on the results of the series of calculations, found, that strategies with the least amount of acute-angle transitions should be chosen. It is described that the increase in accuracy in the considered layouts of the glide equipment can be provided by adjusting the original trajectory when its curvature and the direction of the tool movement change. For such a task, it is necessary to determine as thoroughly as possible the general relationship for the force factors of processing.

Author Biographies

D. A. Dmitriev, Kherson National Technical University

Професор кафедри транспортних систем і технічного сервісу Херсонського національного технічного університету

S. A. Rusanov, Kherson National Technical University

Доцент кафедри транспортних систем і технічного сервісу Херсонського національного технічного університету

A. A. Omelchuk, Kherson National Technical University

Асистент кафедри технічної кібернетики Херсонського національного технічного університету

D. D. Fedorchuk, Kherson National Technical University

Магістрант Херсонського національного технічного університету

References

  1. Afonin, V.L., Krainev, A.F. and Kovalev, V.E. (2001), Obrabatyvayushchee oborudovanie novogo pokoleniya. Kontseptsiya proektirovaniya [New generation processing equipment. The concept of design], in Afonin, V.L. (ed.), Mashinostroenie, Moscow, Russia.
  2. Kuznetsov, Yu.M., Dmitriev, D.O. and Dinevych, G.Yu. (2009), “Layouts of machine-tools with mechanisms of parallel structure”, Monograph red. in Kuznetsov, Yu.М. (ed.), PE Vyshemirskiy, V.S, Kherson, Ukraine.
  3. Kuznetsov, Y.N., Dmitriev, D.O. (2017), “Realization of frame-configurations conception of machine-tools with mechanisms parallel structure”, Journal of the Techical University of Gabrovo, vol. 54. pp. 27-31.
  4. Hennes, N. E. (2002), An Innovative Machinery Concept for High-Performance Components in Aircraft Engineering [3-rd Chemnitz Parallel Kinematics Seminar: Development Methods and Application Experience of Parallel Kinematics], Chemnitz, Germany.
  5. Zhang, D. (2000), Kinetostatic Analysis and Optimization of Parallel and hybrid Architectures for Machine Tools, Ph.D. Thesis, Laval University, Canada.
  6. Kuznietsov, Yu.M., AL-Refo I.F.S. and Dmitriev, D.O. (2013), “Construction and Research of Pyramidal Arrangement Milling Machine-Tool of "Triglide" Type”, International Journals of Engineering & Sciences, International Journal of Mechanical & Mechatronics Engineering, vol. 13, no. 04, August, pp. 24-28.
  7. Dmitriev, D. (2015), New layout and kinematic drill-milling machines with parallel structure mechanisms, Technological Complexes, vol. 1(11), pp. 25-29.
  8. Dmitriev, D.O. (2011), “Description configurations of machine-tools with the mechanisms of parallel structure”, Scientific journal “Technological Complexes”, no 3, pp.18-30, http://t-komplex.net.ua/content/1-11-2015/003.pdf
  9. Hurzhii, A.A. (2015), Formoutvorennia kryvoliniinykh poverkhon na verstatakh z paralelnymy kinematychnymy strukturamy [Formation of curvilinear surfaces on machines with parallel kinematic structures], Ph.D. Thesis, NTUU “KPI”, Kyiv, Ukraine.
  10. Kuznetsov, Y.N., Dmitriev, D.A. and Keba, P.V. (2012), “Kinetic-Static analysis and inflexibility of drilling-milling machine-tool of pyramidal arrangement (DMMPA) with mechanisms of parallel structure (PKM), “12-th Anniversary International scientific Conference "UNITECH -12”, Gabrovo, Bulgaria, 19-20 November, Vol. 2.
  11. Kuznetsov, Yu.N., Keba, P. and Nedelcheva, P.M. (2013), “Uprugo-napryazhennoe sostoyanie nesushchei sistemy stanka piramidal'noi komponovki” [Elastic-stressed state of the bearing system of the machine of the pyramidal configuration], Mezhdunarodnaya nauchno-prakticheskaya konferentsiya “UNITECH-13”, Gabrovo, Bulgaria, pp. 66-69.
  12. Kuznetsov, Yu.N., Nedelcheva, P.M., Stepanenko, A.A. and Manzhola, M.Yu. (2013), “Issledovanie vliyaniya ugla naklona granei karkasa na ego uprugo-napryazhennoe sostoyanie” [Investigation of the effect of the angle of inclination of the facets of the framework on its elastic-stressed state], Mezhdunarodnaya nauchno-prakticheskaya konferentsiya “UNITECH-13”, Gabrovo, Bulgaria, pp. 82-87.
  13. Kuznetsov, Yu.M. (2011), “The development of the design theory of new machine-tools configurations based on system analysis and synthesis of mechanisms of parallel structure”, Research report №2267-F, NTUU “KPI”, Kyiv, Ukraine.
  14. Dmitriev, D.O. (2015), “New Layout and Kinematic Drill-Milling Machines with Parallel Structure Mechanisms”, Scientific journal “Technological Complexes” no 11, pp. 25-30.
  15. Rusanov, S.A., Dmitriev, D.O., Kuznetsov, Yu.M. and Keba, P.V. (2016), Svidotstvo pro reyestraciu avtorskogo prava na tvir Compyuterna programa “ToolsGLIDE”, № 66227, 21.06.2016, Dergavna slugba intelektualnoi vlasnosti Ukrainu.
  16. Rusanov, S.A., Dmitriev, D.O., Kuznetsov, Yu.M. and Podolskyi, M.I. (2014), Svidotstvo pro reyestraciu avtorskogo prava na tvir «Compyuterna programa “Tools App”, № 57913, 29.12.2014, Dergavna slugba intelektualnoi vlasnosti Ukrainu.
  17. Rusanov, S.A., Dmitriev, D.O. (2016), “Kompleksnyi analiz mekhanizmiv paralelnoi struktury zasobamy tsilovykh system avtomatyzovanoho modeliuvannia [Complex analysis of mechanisms of parallel structure by means of target automated modeling systems]”, VII mizhnarodna naukovo-tekhnichna konferentsiya “Teoretychni ta praktychni problemy v obrobtsi materialiv tyskom i yakosti fakhovoi osvity”, Kyiv and Kherson, Ukraine, pp. 152-155.
  18. Dmitriev, D.O., Rusanov, S.A., Keba, P.V. and Piven, S.M. (2016), “Zovnishni moduli dlia prohnozuvannia ta upravlinnia skladnymy rukhamy lanok mekhanizmiv paralelnoi struktury” [External modules for prediction and control of complex movements of links of mechanisms of parallel structure], VI mizhnarodnoi naukovo-praktychnoi konferentsii “Kompleksne zabezpechennia yakosti tekhnolohichnykh protsesiv ta system (KZIaTPS – 2016)”, ChNTU, Chernihiv, Ukraine, pp. 44-47.
  19. Bahanov, Ye.O. Bardachov, Yu.M. and Rusanov, S.A. (2016), “Zastosuvannia virtualnoho potentsialu dlia modeliuvannia prostorovykh mekhanizmiv iz viaziamy” [Application of virtual potential for simulation of spatial mechanisms], Bulletin of Kherson National Technical University, no. 1(56), pp. 25-31.
  20. Rusanov, S.A., Rachynskyi, V.V. and Dmitriev, D.O. (2016), “Prostorovyi analiz sharnirno-stryzhnevykh mekhanizmiv dlia mekhanichnoi obrobky poverkhnevym zmitsnenniam skladno profilnykh detalei” [Spatial analysis of hinge-rod mechanisms for machining with surface hardening of complex profiled parts], II vseukrainska konferentsiya “Pryladobuduvannia i metrolohiia. Suchasni problemy, tendentsii rozvytku”, LNTU, Lutsk, Ukraine, pp. 81-83.
  21. Rusanov, S.A., Dmitriev, D.O. and Rachynskyi, V.V. (2016), “Pratsezdatnist obladnannia karkasnykh komponovok v umovakh sylovoho navantazhennia pry obrobtsi skladnykh detalei poverkhnevym plastychnym deformuvanniam” [The efficiency of the equipment of frame structures in the conditions of power loading in the processing of complex parts by surface plastic deformation], Bulletin of Kherson National Technical University, no 4(59), pp. 43-49, http://kntu.net.ua/index.php/rus/content/download/48947/287985/file/%D0%92%D1%96%D1%81%D0%BD%D0%B8%D0%BA%20%E2%84%964(59).pdf

Downloads

Published

2017-12-29

How to Cite

[1]
D. A. Dmitriev, S. A. Rusanov, A. A. Omelchuk, and D. D. Fedorchuk, “Development of technical means for designing technological and machine equipment for frame layout”, Mech. Adv. Technol., no. 3(81), pp. 54–62, Dec. 2017.

Issue

No. 3(81) (2017)

Section

Original study

License

Copyright (c) 2020 Mechanics and Advanced Technologies

Creative Commons License

This work is licensed under a Creative Commons Attribution 4.0 International License.

The ownership of copyright remains with the Authors.
 
Authors may use their own material in other publications provided that the Journal is acknowledged as the original place of publication and National Technical University of Ukraine “Igor Sikorsky Kyiv Polytechnic Institute” as the Publisher.

Authors who publish with this journal agree to the following terms:

  1. Authors retain copyright and grant the journal right of first publication with the work simultaneously licensed under CC BY 4.0 that allows others to share the work with an acknowledgement of the work's authorship and initial publication in this journal.

  2. Authors are able to enter into separate, additional contractual arrangements for the non-exclusive distribution of the journal's published version of the work (e.g., post it to an institutional repository or publish it in a book), with an acknowledgement of its initial publication in this journal.

  3. Authors are permitted and encouraged to post their work online (e.g., in institutional repositories or on their website) prior to and during the submission process, as it can lead to productive exchanges, as well as earlier and greater citation of published work