Devices for mounting self drilling metal screws

Authors

  • Liudmyla Danylova Igor Sikorsky Kyiv Polytechnic Institute, Kyiv, Ukraine
  • T. Waiyaki Igor Sikorsky Kyiv Polytechnic Institute, Kyiv, Ukraine

DOI:

https://doi.org/10.20535/2521-1943.2019.85.158759

Keywords:

SR screws (self-drilling thread screws), self-drilling forming screw, screw connections, assembly automation

Abstract

Purpose.  Design, manufacture and test the assembly tools for the self-drilling screws. Devices meet the requirements of hard location the screw, based on the outer diameter of the thread, the inner diameter of the thread or jig bushing, while at the end of the screwing, holding elements pass the head of the screw.

Design/methodology/approach. In a paper it is shown that thread-forming screws, known as self-tapping screws capable of forming or rolling a matching thread into the material into which they are installed requires a hard location of the screw in device to prevent action the radial component of the cutting force. And at the same time devices, that meet the requirements of hard location the screw in the locator, at the end of the screwing let the screw head through them. The presented devices hold the screws for the outer diameter of the thread, the inner diameter of the thread or jig bushing. A device designed to align hex parts, such as screw heads, is also described. Such devices are designed for automated production.

Findings. The developed devices were manufactured and tested. Self-drilling screws drilled holes under the action of axial load, maintaining the correct position and with a free passage of the screw head at the end of drilling. Two of the devices presented are protected by copyright.

Originality/value. In the presented devices assembly with the use of self-drilling forming screws consists in the sequential execution of two diverse operations - first drilling, and then rolling the thread under the action of axial load. In this case, the device rigidly bases the screw, but let the screw head pas sat at the end of drilling. Developed devices can be used in assembly automation

Author Biography

Liudmyla Danylova, Igor Sikorsky Kyiv Polytechnic Institute, Kyiv

доцент кафедри технології машинобудування

References

  1. Petrikov, V.G. and Vlasov, A.P. (1991), Progressivnye krepezhnye izdeliya [Progressive fasteners], Masynostroenye, Moscow, Russia.
  2. Arpent'ev, B.M., Zenkin, A.S. and Kutsin, A.N. (1994), Mekhanizatsiya i avtomatizatsiya sborochnykh rabot na mashinostroitel'nykh predpriyatiyakh [Mechanization and automation of assembly work at machine-building enterprises], Tehnika, Kyiv, Ukraine.
  3. Liudmyla, D. (1998), Technological quality assurance of connections with self-tapping fasteners. Ph.D. Igor Sikorsky Kyiv Polytehcnic Institute.
  4. Berezin S.Ya., Kurbatova L.S., Leonov V.N. (2011), “The history of inventions auxiliary equipment for threading and assembly operations”, Scientific notes Transbaikalian State University. A series of physics, mathematics, technology, technology, vol. 3, pp. 6-14.
  5. Berezin S. Ya. and Romanova, L.S. (2013), “Cartridges for threading and assembly operations with special functions”, Assembly in mechanical engineering, instrument making, vol. 12, pp. 6-13.
  6. Kurbatova, L. S. (2016), “Analysis of the use of auxiliary equipment for assembly and threading operations”, Scientific notes Transbaikalian State University. A series of physics, mathematics, technology, technology, pp. 62-63.
  7. Zhdanov, A.V., Smirnov, V.Yu., Dereventsev, M.S., Mikhailov, R.G. and Tolstobrov, V.V. (2015), “Forecasting the reliability of thread-cutting process equipment”, Research publications.
  8. Berezin, S.Ya. and Romanova, L.S. (2013), “Calculation of design and tuning parameters of assembly and thread-cutting cartridges”, Assembly in mechanical engineering, instrument making, vol. 5, pp. 28-34.
  9. Danilova, L.M. Davygora, V.N. and Pasechnik, V.A (1993), Adaptive screwdriver head, Ukraine, Pat. 1808654.
  10. Danilova, L.N. and Yarmosh, A.G. (1989), Part orientation device, Ukraine, Pat. 1484582.

Downloads

Published

2019-04-14

How to Cite

[1]
L. Danylova and T. Waiyaki, “Devices for mounting self drilling metal screws”, Mech. Adv. Technol., no. 1(85), pp. 125–130, Apr. 2019.

Issue

No. 1(85) (2019)

Section

Original study

License

Copyright (c) 2020 Mechanics and Advanced Technologies

Creative Commons License

This work is licensed under a Creative Commons Attribution 4.0 International License.

The ownership of copyright remains with the Authors.
 
Authors may use their own material in other publications provided that the Journal is acknowledged as the original place of publication and National Technical University of Ukraine “Igor Sikorsky Kyiv Polytechnic Institute” as the Publisher.

Authors who publish with this journal agree to the following terms:

  1. Authors retain copyright and grant the journal right of first publication with the work simultaneously licensed under CC BY 4.0 that allows others to share the work with an acknowledgement of the work's authorship and initial publication in this journal.

  2. Authors are able to enter into separate, additional contractual arrangements for the non-exclusive distribution of the journal's published version of the work (e.g., post it to an institutional repository or publish it in a book), with an acknowledgement of its initial publication in this journal.

  3. Authors are permitted and encouraged to post their work online (e.g., in institutional repositories or on their website) prior to and during the submission process, as it can lead to productive exchanges, as well as earlier and greater citation of published work