Estimation of limit state for quasi-isotropic [90°/± 45°/0°]S AS4/3501-6 carbon/epoxy under uniaxial and biaxial loads

Authors

DOI:

https://doi.org/10.20535/2521-1943.2019.86.176173

Keywords:

estimation of limit state, biaxial stress state, laminated carbon fiber reinforced plastic, composite materials, elastic constants.

Abstract

Background. Composite materials, in particular laminated carbon fiber reinforced with high-strength unidirectional fibers, are widely used in many industries. The active development of the production of fibers and matrices leads to a large number of new materials and their widespread using in production requires effective techniques for estimate the ultimate state of carbon fiber under various load conditions.

Objective. Comparative analysis of strength estimation methods using the example of laminated carbon fiber with AS4 carbon fiber and a 3501-6-epoxy matrix reinforcing pattern [90 ° / ± 45 ° / 0 °] s under UNIAXIAL AND BIAXIAL LOADS conditions using an analytical model of the degradation of the mechanical properties of the composite layer proposed in the work of M.K. Kucher and M.M. Zarazovskii and the method of numerical simulation in the software environment ANSYS Workbench.

Methods. The mechanical characteristics of the carbon fiber monolayer were previously calculated using various analytical methods: the mixture rule, the coaxial cylinder method, the Kilchinsky model, and the Vanin method. The stress calculations were compared with tests results published by a group of authors (P. D. Soden, M. J. Hinton & A. S. Kaddour).

Results. The application boundaries for numerical and analytical methods for assessing the strength of carbon plastics in a plane and linear stress state are analyzed.

Conclusions. Based on the studies, it was concluded that the model of degradation of the mechanical properties of the layer requires improvement under conditions of a negative ratio between the main stresses. The effectiveness of using the ACP(Pre) and ACP(Post) modules of the ANSYS Workbench software environment for estimation the ultimate state of laminated carbon fiber reinforced plastic under uniaxial and biaxial loads conditions is confirmed.

Author Biography

S. Shukayev, Igor Sikorsky Kyiv Polytechnic Institute, Kyiv

доктор технічних наук, професор, професор кафедри динаміки і міцності машин і опору матеріалів

References

  1. Kucher, М. and Zarazovskii, M. (2009), “Otsinca mitsnosti sharuvatych plastykiv iz vrachuvannjam degradatsii mechanichnyh haracterystyk v protsesi deformuvannja”, National Technical University of Ukraine "Kyiv Polytechnic Institute". Series of mechanical engineering.Vestnik NTUU «KPI». Serija Mashynostroenie, vol. 57, pp. 174 – 179.
  2. Zarazovskii, M. (2009), Deformuvannja i mitsnist sharuvatyh vugleplastykiv pry kimnatni i kriogennuh temperaturah: dissertation of PhD in Technical Sciences: 01.02.04, Kiev, Ukraine.
  3. Soden, P.D., Hinton, M.J. and Kaddour, A.S. (1998), “Lamina properties, lay-up configurations and loading conditions for a range of fiber-reinforced composite laminates”, Composites Science and Technology, vol. 58, no. 7, pp. 1011 – 1022. https://doi.org/10.1016/S0266-3538(98)00078-5
  4. Rubashevskyi, V., Zarazovskii, M. and Shukyev, S. (2017), “Analysis of methods for determination of the constants of elasticity unidirectional layer composite materials”, Mechanics and Advanced Technologies, vol. 80. no. 2, pp. 107 – 112. http://dx.doi.org/10.20535/2521-1943.2017.80.109634
  5. Horoshun, L. (1993), Staticheskaja machanica i efectivnye svoystva materialov [Статистическая механика и эффективные свойства материалов], Mechanica compositov, in Guzja A.N. (ed.), Nauk. Dumka, Kiev, Ukraine.
  6. Soden, P.D., Hinton, M.J. and Kaddour, A.S. (2002), “Biaxial test results for strength and deformation of a range of E-glass and carbon fibre reinforced composite laminates: failure exercise benchmark data”, Composites Science and Technology, vol. 62, no. 12, pp. 1489 – 1514.
  7. https://www.academia.edu/34789815/TUTORIAL_ACP_PRE_POST
  8. Masley, V., Bobyr, N., Rudakov, K., Popel’, V. and Kulyk, A. (2019), “About Defening moduls of elasticity of composite material layer” ISTC, The Progressive Technics, Technology and Engineering Education, pp. 365 – 368.
  9. Dyfuchyn, Y. and Rudakov, K. (2017), Numerical modelling of bolted composite joints. Bolts rigidity effect on normal stresses in the composite layers, Mechanics and Advanced Technologies, vol. 79, no. 1, pp. 19 – 25. http://dx.doi.org/10.20535/2521-1943.2017.79.95756
  10. Tsybenko, Alexsandr, Borys Rassamakin, Rybalka, Anton (2017), “Strength of nanosatellite POLITAN-2 in action of random loads at stage of transfer to orbit”, Mechanics and Advanced Technologies, vol. 81, no. 3, pp. 28 – 33. http://dx.doi.org/10.20535/2521-1943.2017.81.114113
  11. Karpov, Ja. and Stavychenko, V. (2010), “Metodika rascheta na prochnost’ sloistyh kompozicyonnyh materialov pty termomehanichnyh nagrugenyi”, Strength of Materials, no. 4. pp. 154 – 164.

Published

2019-11-23

How to Cite

[1]
V. Rubashevskyi and S. Shukayev, “Estimation of limit state for quasi-isotropic [90°/± 45°/0°]S AS4/3501-6 carbon/epoxy under uniaxial and biaxial loads”, Mech. Adv. Technol., no. 2(86), pp. 7–13, Nov. 2019.

Issue

Section

Mechanics