С. Ан. Клименко, Ю. Е. Рижов, В. В. Бурикін


To optimize the processing conditions, it is necessary to create opportunities for the cutting temperature controlling, because for each pair of tools – detail materials there is an optimal value of this parameter. Machining with conditions that match the optimal cutting temperature ensures maximum tool life. The practical solution of the problem is possible through the use of wear-resistant coatings. The presence of protective coatings at the contact surfaces of the instrument leads to the changes in mechanical, physical and chemical contact interaction between tool and the work piece. The nanocomposite coating, representing a new generation of materials, based on n-TiC/α-C was used at this paper. They consist of at least two phases of nanocrystalline and amorphous structure and have lower mechanical properties (hardness and elastic modulus) than the base material. The results of experimental researches showed that using the tools with such coatings reduces the average cutting temperature. It is due to the fact that the coating reduces the adhesion interaction between tool and working material leading to the friction declination.


wear resistant coatings; the turning; CBN cutting tools; cutting temperature; operability


Tabakov V. P., Chihranov A.V. Iznosostojkie pokrytija rezhushhego instrumenta, rabotajushhego v uslovijah nepreryvnogo (Wear Resistant Coatings of cutting tools, working in continuous cutting rezanija). Ul'janovsk: UlGTU, 2007. 255 p.

Fomenko R. N. Issledovanie iznosostojkih pokrytij instrumenta na razlichnye parametry processa rezanija pri tochenii (Study of tool wear resistant coatings on various parameters of the cutting process in turning). Ufa: UGATU, 2009. T. 12. No 4(33). pp. 51–55.

Vereshhaka A. S. Rabotosposobnost' rezhushhego instrumenta s iznosostojkimi pokrytijami (The efficiency of cutting tool with wear-resistant coating). Moscow: Mashinostroenie, 1993. 366 p.

Titov V. B. Pokrytija dlja rezhushhego instrumenta: sostojanie voprosa i perspektivy (Coatings for cutting tools: status of the problem and prospects). Instrumental'nyj portal «Vnedrenie info». 2005. pp. 26-29.

Kopejkina M. Ju., Klimenko S.A., Mel'nijchuk Ju.A., Beresnev V.M. Rabotosposobnost' rezhushhego instrumenta, osnashhennogo PSTM na osnove KNB s vakuumno-plazmennym pokrytiem (The efficiency of CBN cutting tool equipped with vacuum plasma coating). Sverhtverdye materialy, 2008. No 5. pp. 87-97.

GOST Style Citations

1. Табаков В. П. Износостойкие покрытия режущего инструмента, работающего в условиях непрерывного резания / В.П. Табаков, А.В. Чихранов. – Ульяновск: УлГТУ, 2007. – 255 с.


2. Фоменко Р. Н. Исследование износостойких покрытий инструмента на различные параметры процесса резания при точении. – Уфа: УГАТУ, 2009. – T. 12. – № 4(33). – С. 51–55.


3. Верещака А. С. Работоспособность режущего инструмента с износостойкими покрытиями. – М.: Машиностроение, 1993. – 366 с.


4. Титов В. Б. Покрытия для режущего инструмента: состояние вопроса и перспективы. – Инструментальный портал «Внедрение инфо». – 2005. – С. 26-29.


5. Копейкина М. Ю. Работоспособность режущего инструмента, оснащенного ПСТМ на основе КНБ с вакуумно- плазменным покрытием / М.Ю. Копейкина, С.А. Клименко, Ю.А. Мельнийчук, В.М. Береснев // Сверхтвердые материалы, 2008. – № 5. – С. 87-97.

Copyright (c) 2020 Journal of Mechanical Engineering NTUU "Kyiv Polytechnic Institute"