APPLICATION OF PLASTICS IN THE BUILDING OF FLUID POWER ELEMENTS

Authors

  • Jarosław Stryczek Wroclaw University of Technology, Wroclaw, Poland
  • Krzysztof Biernacki Wroclaw University of Technology, Wroclaw, Poland
  • Justyna Krawczyk Wroclaw University of Technology, Wroclaw, Poland
  • Józef Wołodźko Wroclaw University of Technology, Wroclaw, Poland

DOI:

https://doi.org/10.20535/2305-9001.2014.71.35363

Keywords:

POM-type plastic, hydraulic elements

Abstract

In the paper, a design concept and models of basic POM-type plastic hydraulic elements such as a gerotor pump, a pressure relief valve, an On – Off valve and a cylinder have been presented. The experimental research proved the elements work properly. A simple system made of the elements has been built. The system worked properly within the working pressure range up to 4MPa. Application of POM is advantageous for its simple and cheap method of production and silent operation.

Further research will be focused on higher strength plastics, development of new design solutions for the elements and better methods of their manufacture

References

1. Bonanno A. Matarialli plastici, caratte ristiche a limitti. Oleodynamica Pneumatica, article 2008, p-p 68-73.

2. Bełzowski, A. ; Stróżyk, P. Assessment of repair reinforcement of polyester-glass fibre pipe. KOMPOZYTY Nr 2/2008, pages. 179-184.

3. Biernacki K., Stryczek J. Analysis of stress and deformation in plastic gears used in gerotor pumps. The Journal of Strain Analysis for Engineering Design, October 2010, vol. 45, Issue 7, pages 465-479.

4. J. Stryczek, S. Bednarczyk, K. Biernacki. Strength analysis of the polyoxymethylene cycloidal gears of the gerotor pump. Archives of Civil and Mechanical Engineering 2014. http://dx.doi.org/10.1016/j.acme.2013.12.005. ARTICLE IN PRESS.

5. J. Stryczek, S. Bednarczyk, K. Biernacki. Gerotor pump with POM gears: Design, production, technology, research. Archives of Civil and Mechanical Engineering 2014. http://dx.doi.org/10.1016/j.acme.2013.12.008. ARTICLE IN PRESS.

6. Bednarczyk S., Biernacki K., Stryczek, J. Application of plastics in manufacture of the gerotor pump .The Twelfth Scandinawian International Conference on Fluid Power SICFP’11. May 18- 20, 2011, Tampere Finland. Vol. 3(4), pages 369-383.

7. Stryczek J., Wołodźko J. Projektowanie węzłów uszczelniających cylindrów hydraulicznych. Opracowanie wewnętrzne Politechniki Wrocławskiej (Design of joints sealing hydraulic cylinders. Develop internal Wroclaw University of Technology). Wrocław 2009.

8. Stryczek J., Wołodźko J. Projekt wstępny cylindra hydraulicznego z tworzyw sztucznych. Opracowanie wewnętrzne Politechniki Wrocławskiej.(Preliminary design of the hydraulic cylinder of plastic. Develop internal Wroclaw University of Technology) Wrocław 2011.

9. Stryczek J., Wołodźko J. Projekt wstępny zaworu zwrotnego i maksymalnego z tworzyw sztucznych. Opracowanie wewnętrzne Politechniki Wrocławskiej (Preliminary design of the check valve and a maximum of plastics. Develop internal Wroclaw University of Technology). Wrocław 2012.

Downloads

Published

2014-12-24

Issue

Section

Статті