DOI: https://doi.org/10.20535/2305-9001.2012.66.38620

FIELD-PERFORMANCE DATA OF SURFACES OF DETAILS OF BLOCK AND MODULAR TURNING CUTTERS AND THEIR MAINTENANCE

А. Н. Кравцов

Abstract


The system of complex parametres is considered which was applied to technological maintenance of field-performance data of details of block and modular turning cutters. The technique of two-level maintenance of these properties with application of graphic methods of system optimization is considered. Designs of turning cutters, their system analysis and results of experimental researches are considered.

The purpose: the Exposition of block-modular turning cutting tools as plant of technological probe at security of their operation properties, systematisation of methods of simulation with application of complex parametres of a condition of surfaces.

Probe: Consists in apply the two-stage circuit of technological security of operation properties of surfaces of details of cutting tools with application of technological and settlement-design values of complex parametres with their subsequent comparison by certain criteria.

Results: Probes of details of block-modular turning cutting tools have confirmed validity of a regulation of a condition of their surfaces by means of complex parametres. For block-modular turning cutting tools, their such indexes as linear deterioration, magnitude of destroying feeding, etc. at the same regulated parametres of quality of surfaces of details of these instruments, had a smaller variance of dispersion, than at use of a traditional technique of a regulation of a condition of their surfaces. Also, introduction of simulation of technological security of operation properties of surfaces of instruments, by means of system optimisation, allows in the course of working out of master schedules, most completely to use possibilities of methods of their handling

Keywords


The field-performance data; block and modular tool

References


1. Ryzhov E.V. Technological heightening methods wear resistance of details. Kiev.: Sciences Thought. 1984. 272 p.

2. Engineering of surfaces of details: Collective of authors; Under the editorship of A.G.Suslov. Moscow: "Machine industry", 2008. 320 p.

3. Kragelsky I.V,. M.N. Dobychin, V.S. Kombalov Friction and Wear: Calculation Methods; Elsevier Science & Technology, 1982. 450 p.

4. Kravtsov A.N., KravtsovN.V. Maintenance of field-performance data of surfaces of details at manufacture: Enclosed joint-stock about-in "ONIKS" (Join scientific, engineering and commercial structures) - Irbit: ONIKS, 2011. 261 p.

5. Kravtsov N.V. Heightening of reliability and longevity of block-modular instruments , Problems of improvement in quality, reliability and longevity. - Bryansk: Publishing house BITM, 1989. pp. 118 - 123.

6. Kravtsov N.V., A.A.Klochko Application of complex parametres at technological security of field-performance data of modular instruments, The Advanced know-how and scientific and technical reachings: the Informational collector. - VNIITEMR. 1990. No. 4. pp. 11 - 12.

7. Kravtsov N.V, A.N. Kravtsov. Complex parametres of a condition of surfaces of details of block-modular turning cutting tools The Journal «Omsk scientific bulletin». no 3 (113). Omsk: Publishing house OmSTU, 2012 - (p. 162 - 166).

8. Kravtsov A.N. Geometrical simulation of correlation of field-performance data of surfaces of details of block-modular turning cutting tools with their indexes of quality by means of graph theories The Journal «Vector of a science of the Tolyatti state university». No. 3 (21). - Tolyatti: Publishing house TSU, 2012,pp. 89 - 93.


GOST Style Citations


1.            Рыжов Э.В. Технологические методы повышения износостойкости деталей машин. Киев.: Наук. Думка. 1984. – 272с.

 

2.            Инженерия поверхностей деталей [Текст] / Колл. авт.; Под ред. А.Г. Суслова. М.: «Машиностроение», 2008. – 320 с.

 

3.            Kragelsky I.V. Friction and Wear: Calculation Methods / I.V. Kragelsky, M.N. Dobychin, V.S. Kombalov; Elsevier Science & Technology, 1982. - 450 p.

 

4.            Кравцов А.Н. Обеспечение эксплуатационных свойств поверхностей деталей при изготовлении [Текст] / А.Н. Кравцов, Н.В. Кравцов; Закрытое акционерное об-во "ОНИКС" (Об-ние науч., инженерных и коммерческих структур) - Ирбит: ОНИКС, 2011. – 261 с.

 

5.            Кравцов Н.В. Повышение надежности и долговечности блочно-модульных инструментов [Текст] / Н.В. Кравцов // Проблемы повышения качества, надежности и долговечности машин. - Брянск : Изд-во БИТМа, 1989. – (с. 118 – 123).

 

6.            Кравцов Н.В. Применение комплексных параметров при технологическом обеспечении эксплуатационных свойств сборных инструментов [Текст] / Н.В. Кравцов, А.А. Клочко // Передовой производственный опыт и научно-технические достижения: Информационный сборник. - ВНИИТЭМР. 1990. - Вып. 4. – (с. 11 – 12).

 

7.            Кравцов Н.В. Комплексные параметры состояния поверхностей деталей блочно-модульных токарных резцов [Текст] / Н.В. Кравцов, А.Н. Кравцов // Журнал «Омский научный вестник». Серия: Приборы, машины и технологии. № 3 (113). – Омск: Изд-во ОмГТУ, 2012 - (с. 162 - 166).

 

8.            Кравцов А.Н. Геометрическое моделирование взаимосвязи эксплуатационных свойств поверхностей деталей блочно-модульных токарных резцов с их показателями качества при помощи теории графов [Текст] / Кравцов А.Н. // Журнал «Вектор науки Тольяттинского государственного университета». № 3 (21). – Тольятти: Изд-во ТГУ, 2012 - (с.89 - 93).





Copyright (c) 2020 Journal of Mechanical Engineering NTUU "Kyiv Polytechnic Institute"