THE ANALYSIS OF BLOCK PRESSING PROCESS OF THE CYLINDER NECKS ON TUBULAR PREFORMS IN A SPHERICAL MATRIX WITH A DIFFERENTIATED BACKPRESSURE

Authors

  • О. В. Калюжний National Technical University of Ukraine "Kyiv Polytechnic Institute", Kyiv, Ukraine

DOI:

https://doi.org/10.20535/2305-9001.2012.66.38986

Keywords:

block pressing, spherical matrix, differentiated backpressure, finite element method

Abstract

The method of obtaining of cylinder necks by block pressing with the backpressure on an internal surface of preform is presented. The finite element method carries out the calculated analysis of traditional block pressing and block pressing with a backpressure of cylinder necks on tubular preforms in a spherical matrix. Finite shapes of products are defined at traditional block pressing and block pressing with a backpressure. The backpressure usage eliminates fracture of the preform metal at a deforming and heightening of cylinder necks. Force conditions of the preforms forming, the stress-strain state of metal and exact sizes of cylinder necks are calculated. Backpressure operation leads to heightening of intensity of strains and a reinforcement of metal after block pressing.The aforesaid ensures reliability of a screw joint of the block pressed articles with other details.The further explorations of block pressing with a backpressure are necessary to lead in a direction of obtaining of cylinder necks on the hollow articles with a bottom, and also determinations of effect of width of a wall of preform on cylinder necks forming.

Author Biography

О. В. Калюжний, National Technical University of Ukraine "Kyiv Polytechnic Institute", Kyiv

к.т.н.

References

1. KaljuzhnijV. L.,KaljuzhnijO. V., PіmanovV. V., Paljanichko Є. M.Sposіbobtiskugorlovinitipubalon: pat. Ukraїni no.59190: MPK V21V26/02; Zajavnik і patentovlasnik NTUU „KPІ”; Opubl. 10.05.2011, bjul. no 9.

2. Kaljuzhnij O.V. Analіz silovih rezhimіv ta jakostі virobіv pri obtisku trubchatih zagotovok v konusnіj matricі.JournalofMechanicalEngineeringofthe National Technical University of Ukraine “Kyiv Politechnic Institute”, 2011, vip. 62. pp. 63-67.

3. Kaljuzhnij O.V. Porіvnjal'nij analіz tradicіjnogo obtisku ta obtisku z diferencіjovanim protitiskom. Vіsnik Nacіonal'nogo tehnіchnogo unіversitetu «HPІ». Zbіrnik naukovih prac'. Tematichnij vipusk : novі rіshennja v suchasnih tehnologіjah: - Harkіv: NTU «HPІ», 2011. 46. pp. 27-34.

4. Popov E.A. Osnovy teorii listovoj shtampovki: uchebnoe posobie dlja vuzov. Moscow: Mashinostroenie, 1977. 278 p.

5. Romanovskij V.P. Spravochnik po holodnoj shtampovke. 6-e izd., pererab. i dop. Lviv: Mashinostroenie. Leningr. otd-nie, 1979. 520 p.

6. Kovka i shtampovka: Spravochnik: V 4 t. T. 4 Listovaja shtampovka. Pod red.. A.D. Matveeva; Red. sovet: E.I. Semenov (pred.) i dr. – Moscow: Mashinostroenie, 1985-1987. 544 p.

7. Averkiev Ju.A. Holodnaja shtampovka. Izdatel'stvo Rostovskogo universiteta, 1984, 288 p.


Published

2015-03-11

Issue

Section

Статті