ABOUT INFLUENCE OF SIZE OF A BACKLASH BETWEEN A BOLT AND THE HOLE ON THE TENSION CONDITION OF A BOLT OF THE SINGLE-SHEAR BOLTED JOINT IN A "SHEARING" ZONE

Authors

  • К. М. Рудаков Націона́льний техні́чний університе́т Украї́ни «Ки́ївський політехні́чний інститу́т», Ukraine https://orcid.org/0000-0003-4191-8945
  • О. А. Добронравов Націона́льний техні́чний університе́т Украї́ни «Ки́ївський політехні́чний інститу́т», Ukraine

DOI:

https://doi.org/10.20535/2305-9001.2013.69.28990

Keywords:

bolted joints, backlash, method of finite elements, 3D contact model, stress-strain condition

Abstract

Purpose. Studying of influence of value of a backlash on a state of stress of a bolt of a single-shear bolt joint in a "shearing" zone.
Methodology. Used a method of final elements and the 3D contact model as much as possible approached to real geometry and conditions of load application.
Findings. The bolt of a single-shear bolt joint always "works" not only on a shear, and on a bending. Contact interaction of a lateral surface of a bolt with edges of apertures calls in zones of contacts in a bolt additional negative axial stresses of peak character. Even at a cycle with a constant sign on the loading in a bolt at a surface there can be a zone with cyclically sign-variable axial stresses, and they are more destructive, than with a constant sign. It changes character of fatigue failure of a bolt.
Originality. The reason of change of character of fatigue failure of a bolt is found out: separation instead of a shear.

References

Prognozirovanie i raschet ustalostnoj dolgovechnosti modelej silovyh konstruktivnyh jelementov s otverstijami na jetapah jeskiznogo i rabochego proektirovanija [Forecasting and calculation of fatigue life of models of power structural members with apertures at stages initial and design engineering] Krivov G.A., Bychkov S.A., Vasilevskij E.T. and others. Otkrytye informacionnye i komp'juternye integrirovannye tehnologii: sb. nauch. tr. Nac. ajerokosm. un-ta im. N.E. Zhukovskogo "HAI". Kharkov, 2010. 45. pp. 51–60. 2. Strizhius V.E. O nekotoryh gipotezah i dopushhenijah pri raschete ustalostnoj dolgovechnosti jelemen-tov aviakonstrukcij iz PKM [About some hypotheses and assumptions at calculation of fatigue life of elements of airframes from composites] Moscow: Nauchnyj vestnik MGTU GA, 2011. no.163(1). pp. 96–102. 3. V.A. Eshwar. Analysis of clearance fit pin joints, Int. J. Mech. Sci., 1978. Vol.20. pp. 477-484. 4. V.P. Lawlor, W.F. Stanley, M.A. McCarthy. Characterisation of damage development in single shear bolted composite joints. Journal of Plastics, Rubber and Composites, 2002. The Institute of Materials, London, UK. Vol.31. No.3, pp. 126-133. 5. V.P. Lawlor, M.A. McCarthy, W.F. Stanley. Experimental study on the effects of clearance on single-bolt, single-shear, composite bolted joints. Journal of Plastics, Rubber and Composites, 2002. The Institute of Materials, London, UK. Vol.31. No.9. pp. 405-411. 6. M.A. McCarthy, C.T. McCarthy. Finite element analysis of the effects of clearance on single-shear, composite bolted joints. Journal of Plastics, Rubber and Composites, 2003. The Institute of Materials, London, UK. Vol. 32. No.2. pp. 65-70. 7. Modelirovanie boltovyh soedinenij, soderzhashhih detali iz PKM, v srede FEMAP/NASTRAN [Modelling of the bolt joints containing details from composites, in program FEMAP/NASTRAN] Krivov G.A., Matvienko V.A., Rud'ko A.N. and others. Technological Systems. Kyiv: UkrNIIAT, 2013. no.1(62). pp. 90–102. 8. Rudakov K.N., Shukaev S.N. Modelirovanie boltovyh soedinenij iz PKM v programmnom komplekse FEMAP/NX NASTRAN [Modeling of bolt joints from composites in program complex FEMAP/NX NASTRAN] Journal of Mechanical Engineering of the National Technical University of Ukraine "Kyiv Polytechnic Institute", 2013. No.67. pp. 199–206. 9. Birger I.A., Iosilevich G.B. Rez'bovye i flancevye soedinenija [Threaded and flange joints] Moscow: Mashinostroenie, 1990. 365 p. 10. Raschet na prochnost' detalej mashin: Spravochnik [Strength calculation of details of machines: the Quick reference] I.A. Birger, B.F. Shorr, G.B. Iosilevich. Moscow: Mashinostroenie, 1979. 702 p. 11. Iosilevich G.B. Koncentracija naprjazhenij i deformacij v detaljah mashin [Stress concentration and strains in details of machines] Moscow: Mashinostroenie, 1981. 224 p. 12. Jonson K.L. Contact mechanics. Cambridge: Cambridge University Press, 1985. 452 p. 13. Ljav A. Matematicheskaja teorija uprugosti [The mathematical theory of elasticity] Moscow, Leningrad: ON-TINKTP SSSR, 1935. 674 p. 14. Timoshenko S.P., Gud'er Dzh. Teorija uprugosti [The elasticity theory] Moscow: Nauka, 1975. 575 p. 15. Titanovye splavy v mashinostroenii [Titanium alloys in machine industry] B.B. Chechulin, S.S. Ushkov, I.N. Razuvaeva and others. Leningrad: Mashinostroenie, 1977. 248 p. 16. Shukaev S.N., Rudakov K.N., Kornev P.A. Vpliv tehnologіchnih faktorіv na mіcnіst' boltovih z’єdnan' z kompozicіjnih materіalіv [Effect of technological factors on the strength of composite bolted joints] Research Bulletin of the National Technical University of Ukraine "Kyiv Polytechnic Institute", 2013. no.5. pp. 93–97.

Published

2014-11-07

Issue

Section

Статті