Corrosive and tribocorrosive behavior of plasma powder coatings

Authors

  • M. S. Khoma Institute of Physics and Physics GV Karpenko NAS of Ukraine, Lviv, Ukraine
  • I. О. Ryabtsev Institute of electric welding them. E.O. Paton NAS of Ukraine, Kyiv, Ukraine https://orcid.org/0000-0001-7180-7782
  • V. A. Vynar Institute of Physics and Physics GV Karpenko NAS of Ukraine, Lviv, Ukraine
  • Kh. B. Vasyliv Institute of Physics and Physics GV Karpenko NAS of Ukraine, Lviv, Ukraine
  • N. B. Ratska Institute of Physics and Physics GV Karpenko NAS of Ukraine, Lviv, Ukraine https://orcid.org/0000-0002-5960-4744
  • V. R. Ivashkiv Institute of Physics and Physics GV Karpenko NAS of Ukraine, Lviv, Ukraine

DOI:

https://doi.org/10.20535/2521-1943.2019.86.181049

Keywords:

plasma-powder surfacing, corrosion, tribocorrosion, hydrogen sulfide, chlorides, ammonia

Abstract

Abstract. Purpose. To investigate corrosion and tribocorrosion characteristics of plasma-powder coatings on the basis of iron, nickel and Fe-Ni system in the envyronments containing chlorides, hydrogen sulfide and ammonia.

Metodology: corrosive-electrochemical, tribological, metallographic methods have been used.

Results It was established that as the pH of the solution increases, the corrosion resistance of the coatings increases. The highest corrosion resistance has a surfaced layer based on nickel 06Х17Н80С3Р3, however, under tribocorrosion conditions, fragile component of coatings form an abrasive in the friction zone that intensifies the destruction. Compared to others, the coating 06Х17Н80С3Р3 has the lowest resistance to corrosion-mechanical destruction.

The fragile component is absent in layers, deposited from powders 01H17N8S6G and 08Х17Н35С3Р. The solid phases are uniformly distributed in a plastic matrix corresponding to the Sharpi-Bochvar rule. In this coatings, the contact interaction occurs in the absence of abrasive wear, which explains the high resistance to tribocorrosion.

It is possible to qualitatively evaluate the processes of formation and destruction of secondary structures in the friction zone of tribocorrosion by comparing of the corrosion potentials, tribocorrosion potentials and passivation potentials. Additional information may be provided by the level of local oscillations of the tribopotential, which characterizes the repassivation rate.

Practical result. A new composition 08Х17Н35С3Р3 for plasma-powder coatings has been proposed to increase the wear and corrosion resistance of steel surface.

References

  1. Pokhmurskii, V., Student, M., Dovhunyk, V., Vynar, V., Pokhmurska, H. and Wielage, B. Grund T., Tribocorrosion properties of coatings arc sprayed with aluminium based cored wires, European corros. congres EUROCORR’07, Dusseldorf, Germany, Paper no. 1351CD ROM.
  2. Favero, M., Stadelmann, P. and Mischler, S. (2006), “Effect of the applied potential of the near surface microstructure of a 316 steel submitted to tribocorrosion in sulfuric acid”, J.Phys. D: Appl. Phys. vol. 39, no. 15, pp. 3175 – 3183.
  3. Landolt, D., Stemp, M, and Mischler, S. (2001), “Electrochemical methods in tribocorrosion: a critical appraisal”, Electrochim. Acta. vol. 46, pp. 3913 – 3929.
  4. Gladkyi, P.B., Pereplotchikov, Е.F. and, Pjabcev, I.А. (2007), Plazmenno-poroshkovaia naplavka [Plasma-povder surfacing], Ecotechnologia, Kiev, Ukraine.
  5. Voitovych, A., Pokhmurs’ka, H. and Student, M. (2016), “Student OMicrostructure and Abrasive-Wear Resistance of the Vibration-Deposited Metal of Core Wires of the Basic Fe–Cr–B System”, Materials Science, vol. 52. no. 3, рp. 365 –370.
  6. Klimpel, A., Dobrzański, L.A., Lisiecki, A. and Janicki, D. (2006), “The study of the technology of laser and plasma surfacing of engine valves face made of X40CrSiMo10-2 steel using cobalt-based powders”, Journal of Materials Processing Technology. vol. 175, no. 1 – 3. pp. 251 – 256, https://doi.org/10.1016/j.jmatprotec.2005.04.050
  7. Pereplotchikov, E. Vasyliv, H. and Vynar, V. and dr. (2018), “Plasma-powder surfacing of high-alloy alloys on the basis of iron, chromium and nickel on low-alloy structural steel in order to increase their wear resistance”, Phycico-chemical mechanics of materials, no. 3. pp. 81 – 88.
  8. Vynar, V.A., Dovhunyk, V.M. and Student, M.M (2011), “Methodical specific features of tribocorrosion investigations”, Materials Science, pp. 633 – 639.
  9. Zakalov, O.V. and Zakalov, I.O. (2011), Osnovy tertia i znoshuvannia v mashynakh [The basics of friction and wear in machines], Navchalnyi posibnyk, Vydavnytstvo TNTU im. I.Puliuia, Ternopil, Ukraine.
  10. Vynar, V.A., Pokhmurskii, V.I. and Zin, I.M. and dr. (2018), “Determination of the Mechanism of Tribocorrosion of D16T Alloy According to the Electrode Potential”, Materials Science, рp. 717 – 723.

Downloads

Published

2019-11-26

How to Cite

[1]
M. S. Khoma, Ryabtsev I. О., V. A. Vynar, K. B. Vasyliv, N. B. Ratska, and V. R. Ivashkiv, “Corrosive and tribocorrosive behavior of plasma powder coatings”, Mech. Adv. Technol., no. 2(86), pp. 125–129, Nov. 2019.

Issue

No. 2(86) (2019)

Section

Up-to-date machines and the technologies of mechanical engineering

License

Copyright (c) 2020 Mechanics and Advanced Technologies

Creative Commons License

This work is licensed under a Creative Commons Attribution 4.0 International License.

The ownership of copyright remains with the Authors.
 
Authors may use their own material in other publications provided that the Journal is acknowledged as the original place of publication and National Technical University of Ukraine “Igor Sikorsky Kyiv Polytechnic Institute” as the Publisher.

Authors who publish with this journal agree to the following terms:

  1. Authors retain copyright and grant the journal right of first publication with the work simultaneously licensed under CC BY 4.0 that allows others to share the work with an acknowledgement of the work's authorship and initial publication in this journal.

  2. Authors are able to enter into separate, additional contractual arrangements for the non-exclusive distribution of the journal's published version of the work (e.g., post it to an institutional repository or publish it in a book), with an acknowledgement of its initial publication in this journal.

  3. Authors are permitted and encouraged to post their work online (e.g., in institutional repositories or on their website) prior to and during the submission process, as it can lead to productive exchanges, as well as earlier and greater citation of published work