Updating of Technological Base of Repair of Components from Polymer Composite Materials of Airframe

Authors

  • Roman Kachmar State Enterprise "Lviv State Aircraft Repair Plant", Lviv, Ukraine https://orcid.org/0000-0002-5440-6853
  • Gheorghij Kryvov JSC "Ukrainian Research Institute of Aviation Technology", Kyiv, Ukraine
  • Dmytro Jermolin State Enterprise "Lviv State Aircraft Repair Plant", Lviv, Ukraine
  • Valerij Matvijenko JSC "Ukrainian Research Institute of Aviation Technology", Kyiv, Ukraine https://orcid.org/0000-0001-8643-3787
  • V. Baklan JSC "Ukrainian Research Institute of Aviation Technology", Kyiv, Ukraine
  • А. Rudjko JSC "Ukrainian Research Institute of Aviation Technology", Kyiv, Ukraine

Keywords:

technological normative basis, airworthiness, polymer composite material, an integral part of the aircraft, operational defect, typical technological process of repair, route technological repair process

Abstract

The article describes and demonstrates the main results of the implemented work package in order to update the technological normative base regulates repair technologies of typical in-use defects of component parts from polymer composite materials (PCM) of airframe MiG-29. It was performed review, addition, clarification of the relevant provisions of the technological documentation of the State Enterprise "Lviv State Aircraft Repair Plant" and it was documented repair technologies in the format of typical technological process (TTP).

The TTP made provision for the use of modern materials for repair with appropriate characteristics of strength and technological effectiveness, and also the wide range of means of technological equipment.

The implementation of the results of the work will contribute to the stability of the quality indicants of repair, reclosing the impact subjective factors on them.

References

  1. G.M. Gunyaev et al., "Polymer composite materials in aircraft structures", Сonversion in mechanical engineering, no. 4, pp. 65–69, 2004. https://doi.org/10.11619/africa1964.2004.65_69
  2. O.M. Dobrydenko et al., "Analysis of existing composite materials and evaluation their application in the designs of airframe military aircraft of Ukraine", Digest of scientific works of the State Research Institute of Aviation, vol. 8, no. 15, pp. 146–152, 2012.
  3. S.V. Ivanov (2005). MiG-29. Available: https://avidreaders.ru/book/mig-29.html
  4. V.V. Murashov and A.F. Rumyantsev, "Defects of monolithic parts and multilayer structures made of polymer composite materials and methods of their detection Part I: Defects of monolithic parts and multilayer structures made of polymer composite materials", 2006 [Online]. Available: https://viam.ru/public/files/2008/2006-204706.pdf [Accessed June 15, 2020].
  5. E.N. Kablov and V.O. Startsev, "A systematic analysis of the influence of climate on the mechanical properties of polymer composite materials according to the data of domestic and foreign sources (review)", Aviation materials and technologies, vol. 2, no. 51, pp. 47–58, 2018. https://doi.org/10.18577/2071-9140-2018-0-2-47-58
  6. V.A. Matvienko, "Information and methodological base of technological design of aviation aeronautical equipment in the CAD/CAM/CAE system", Information sciences technology in knowledge-based engineering, Kyiv, Ukraine: Tekhnika, 2001, pp. 398–405.
  7. V.A. Matvienko et al., "Formation of the domestic normative base of helicopter technology", Technological Systems, vol. 1, no. 67, pp. 33–40, 2014.
  8. Technological documentation system. Terms and definitions. State Standards of Ukraine. DSTU 2391-2010.
  9. Especial technological process. Development and execution of documentation for technological processes of manufacturing products from polymer composite materials in preparation for production, manufacturing and repair of aviation equipment. Methodological Instructive Regulations. MU 1.4.2132-2003, National Institute of Aviation Technologies, JSC [NIAT], 2003, Moscow, RU.
  10. A.P. Bojko, O.M. Dobrydenko and R.V. Kachmar, "Research of the influence of corrosion lesions on the strength of the power structure of the tail fin MiG-29", Digest of scientific works of the State Research Institute of Aviation, vol. 5, no. 12, pp. 162–167, 2009.
  11. O.M. Dobrydenko, R.V. Kachmar and O.I. Kremeshnyj, "Determination of the reasons for the development of corrosion lesions of the fish-plate of the tail fin MiG-29 aircraft", Digest of scientific works of the Kharkiv Air Force University named after Ivan Kozhedub, vol. 2, no. 28, pp. 52–54, 2011.
  12. V.A. Bazhenov et al., "Calculation of the residual strength of the fish-plate affected by corrosion of the tail fin MiG-29", Digest of scientific works of the State Research Institute of Aviation, vol. 16, no. 13, pp. 129–135, 2010.
  13. E.N. Kablov, S.A. Karimova and L.V. Semenova, "Corrosion activity of сarbon fibre reinforced plastic (CFRP) and protection of metal power structures in contact with CFRP", Corrosion: materials, protection, vol. 12, pp. 1–7, 2011.
  14. A.V. Andreev and V.S. Nitka, "Research of pasty aircraft adhesives from the 3M company for bonding and repairing composite panels", The questions of design and produced of the aircraft structures: Digest of scientific works of the National aerospace university "Kharkiv Aviation Institute", vol. 1, pp. 38–50, 2017.
  15. 3M Company. 3M™ "Scotch-Weld™ 7260 – two-pack epoxy adhesive, gray, 400 ml", 2019. [Online]. Available: https://www.3mrussia.ru/3M/ru_RU/company-ru/all-3m-products/~/3M-Scotch-Weld-7260?N=5002385+3294236861&pre- select=3293786499&rt=rud. Last accessed 28th Jul 2020.
  16. L.Kh. Airapetyan et al., Aircraft Adhesives Handbook, Leningrad, Russia: Khimiya, 1980.
  17. Federal State Unitary Enterprise All-Russian Scientific Research Institute of Aviation Materials, "Catalog of materials. Aircraft adhesive VK-9", 2009. [Online]. Available: https://catalog.viam.ru/catalog/vk_9/kley-vk-9/ [Accessed Jul. 28, 2020].
  18. V.A. Matvienko, "The mechanism of the formation of the adhesive bead of adhesive and adhesivemechanical joints", Journal of Mechanical Engineering, vol. 18, 1983.
  19. V.A. Matvienko, V.V. Baranovskii and A.A. Bradulov, "Using the method of multicriteria optimization to determine the parameters of the adhesive bead formation process", Aviation Industry, vol. 5, 1992.

Downloads

Published

2020-12-29

How to Cite

[1]
R. Kachmar, G. . Kryvov, D. Jermolin, V. Matvijenko, V. Baklan, and Rudjko А., “Updating of Technological Base of Repair of Components from Polymer Composite Materials of Airframe”, Mech. Adv. Technol., no. 3(90), pp. 57–63, Dec. 2020.

Issue

No. 3(90) (2020)

Section

Aviation Systems and Technologies

License

Copyright (c) 2020 Роман Качмар, Георгій Кривов, Дмитро Єрмолін, Валерій Матвієнко, В. Баклан, А. Рудько

Creative Commons License

This work is licensed under a Creative Commons Attribution 4.0 International License.

The ownership of copyright remains with the Authors.
 
Authors may use their own material in other publications provided that the Journal is acknowledged as the original place of publication and National Technical University of Ukraine “Igor Sikorsky Kyiv Polytechnic Institute” as the Publisher.

Authors who publish with this journal agree to the following terms:

  1. Authors retain copyright and grant the journal right of first publication with the work simultaneously licensed under CC BY 4.0 that allows others to share the work with an acknowledgement of the work's authorship and initial publication in this journal.

  2. Authors are able to enter into separate, additional contractual arrangements for the non-exclusive distribution of the journal's published version of the work (e.g., post it to an institutional repository or publish it in a book), with an acknowledgement of its initial publication in this journal.

  3. Authors are permitted and encouraged to post their work online (e.g., in institutional repositories or on their website) prior to and during the submission process, as it can lead to productive exchanges, as well as earlier and greater citation of published work