Programming of adaptive machining for end milling

Authors

DOI:

https://doi.org/10.20535/2521-1943.2017.79.97342

Keywords:

adaptive machining, virtual basing, the task of minimax, contour milling

Abstract

The problem of performing adaptive machining to program the milling of the detail contours on the CNC machine in case of virtual-location procurement is solved. The correction of the CNC-program by measuring the actual position of the workpiece on the machine table is proposed, and the correction of the control program can be implemented in the result of solving the task of minimax, when looking for such state of its position in space to the maximum allowance on the machined contour was minimal. A mathematical model is developed that unambiguously identifies the position of the workpiece on the machine table according to the measured coordinates of the three points. The developed algorithms automatically search for the correction of the CNC-program for implementing the principle of adaptive machining solution of the problem of minimax. The soft program is created and the method of designing the CNC-program for a virtual basing of the workpiece on the CNC machine is developed. Experimental testing has confirmed efficiency of the developed technique.

References

  1. Kosilova, А.G., Меsheriakova, R.К. and Suslov, А.G. (2001), Spravochnik tehnologa-mashinostroitelia, in Dalskogo А.М. (ed.), Vol 2, no l, Маshinostroenie, Moscow, Russian.
  2. Кorchak, S.N., Guzeev, V.I., Butorin, G.I., Viboyshik, V.N., Kulygin, V.L. and Shamarin, V.Y. (2006), Teoreticheskie osnovy bazirovania detaley i rascheta razmernyh cepey pri mehanicheskoq obrabotke, Uchebnoe posobie, Коmputernaya versia, 2nd edn, in Guzeeva, V.I. (ed.), YUrGU, Cheliabinsk, Russia.
  3. Obrabotka lopatki turbiny - YouTube https://www.youtube.com/watch?v=k7JJv8T19io
  4. Evchenko, К. (2007), Novie reshenia Delcam dla mehanoobrabotki i dla ludey, SAPR I graphika, no 7, http://www.sapr.ru/article/17844
  5. Primenenie tehnologii OMV I adaptivnoy mehanoobrabotki pry proizvodstve izdeliy iz kompozitnih materialov, Umnoe proizvodstvo, vip. 36 ot 12.16 http://www.umpro.ru/index.php?page_id=17&art_id_ 1=163&group_id_4=74
  6. Adaptivnaia obrabotka ot kompanii Delcam plc kak integracia mehanoobrabotki I kontrolia tochnosti izgotovlenia izdeliy, SAPR I graphika, no 1, 2008, pp. 17-20.
  7. Sysoev, Y.S. and Tomilin, S.А. (2004), Bazirovanie zagotovok krupnogabagitnih cylindricheskih detaley dla obrabotki rezaniem, Izvestia vuzov, Маshinostroenie, no 1, pp.53-58.
  8. Кiselev, I.A. (2012), Geometricheskiy algorytm 3MZBL dla modelirovania processov obrabotki rezaniem. Metodika opisania zagotovki, Vestnik MGTU im. N.E. Baumana. Ser. “Mashinostroenie”, no 6, pp. 158-175.
  9. Petrakov, Y.V. and Simuta, R.R. (2014), Modeluvannia procesu zrizuvannia pripusku pid chas konturnogo frezeruvannia, Vestnik Nacionalnogo universitetu “Lvivska polytehnika” Optimizacia vyrobnichih procesiv I tehnichniy control u mashinobuduvanni ta priladobuduvanni, Lviv, pp.142-148.
  10. Radu Pavel Adaptive Machining for High Precision Fabrication, http://www.mapyourshow.com/MYS_Shared /imts16/handouts/RaduPavelIMTS57.pdf

Downloads

Published

2017-06-22

How to Cite

[1]
Y. Petrakov and D. Shuplietsov, “Programming of adaptive machining for end milling”, Mech. Adv. Technol., no. 1(79), pp. 34–40, Jun. 2017.

Issue

No. 1(79) (2017)

Section

Original study

License

Copyright (c) 2020 Mechanics and Advanced Technologies

Creative Commons License

This work is licensed under a Creative Commons Attribution 4.0 International License.

The ownership of copyright remains with the Authors.
 
Authors may use their own material in other publications provided that the Journal is acknowledged as the original place of publication and National Technical University of Ukraine “Igor Sikorsky Kyiv Polytechnic Institute” as the Publisher.

Authors who publish with this journal agree to the following terms:

  1. Authors retain copyright and grant the journal right of first publication with the work simultaneously licensed under CC BY 4.0 that allows others to share the work with an acknowledgement of the work's authorship and initial publication in this journal.

  2. Authors are able to enter into separate, additional contractual arrangements for the non-exclusive distribution of the journal's published version of the work (e.g., post it to an institutional repository or publish it in a book), with an acknowledgement of its initial publication in this journal.

  3. Authors are permitted and encouraged to post their work online (e.g., in institutional repositories or on their website) prior to and during the submission process, as it can lead to productive exchanges, as well as earlier and greater citation of published work