Heating (thermogenesis) in rapid internal combustion engine
DOI:
https://doi.org/10.20535/2521-1943.2018.82.125201Keywords:
rapid internal combustion engine, heat formation, heat formation intensity, anti (heat)detonation heat dissipationAbstract
The features of heat production in the process of combustion of a fuel mixture in a cylinder of an internal combustion engine are studied. As it turned out, typical of the working processes in the otto-engine internal combustion is that, until the moment of reaching the maximum intensity of heat generation, the total amount of heat dissipated is 49% of the potentially possible — one that conceals the fuel that has fallen into the work engine space. At different operating modes of the engine m, the parameter characterizing together the maximum of the intensity of heat generation and the instant of its onset acquires values close to . These typical features are very durable and it makes sense to rely on the simulation of the internal combustion engine. Often, the proportion of conditionally burned fuel (the proportion of the allocated within the working space of the engine of heat) in the case of modelling of heat generation is considered to be predetermined and fixed. Instead, experiments show that this parameter acquires a completely different meanings at different modes of motion. It is always worthwhile to take into account this fact because it enables to objectively evaluate the efficiency of heat generation. The formal signs (which do not reveal the physical essence) of the optimality of the process of heat generation declared in the scientific literature, it turns out, distinguish such a process of heat release, which is appropriately called anti (heat) detonation. The (heat) detonation of the heat is that in the process of combustion of the fuel mixture the maximum rate of heat release should be as small as possible, that is, the process must become, so to speak, minimax.References
- Hashchuk, P. and Bohachyk, Yu. (1995), “Analitychni zasoby modeliuvannia protsesiv teplotvorennia-teplospozhyvannia v dvyhuni z yaskrovym zapaliuvanniam na yalovykh rezhymakh yoho roboty”, Proektuvannia, vyrobnytstvo ta ekspluatatsiia avtotransportnykh zasobiv ta avtopoizdiv, Pratsi Zakhidnoho naukovoho tsentru Transportnoi akademii Ukrainy, vol. 1, Lviv, Ukraine, pp. 34—51.
- Hashchuk, P. and Bohachyk, Yu. (1995), “Osoblyvosti vnutrishnoho teploperenosu v dvyhuni z yaskrovym zapalenniam za riznykh navantazhen”, Proektuvannia, vyrobnytstvo ta ekspluatatsiia avtotransportnykh zasobiv i poizdiv, Pratsi zakhidnoho naukovoho tsentru Transportnoi akademii nauk, vol. 2, Lviv, Ukraine, pp. 12—15.
- Nikipchuk, S. V. (2016), “Vyznachennia koefitsiienta teploperedachi v dvyhuni pryvodu pozhezhno-riatuvalnoho obladnannia analitychnymy zasobamy”, Materialy Mizhnarodnoi naukovo-praktychnoi konferentsii “Pozhezhna ta tekhnohenna bezpeka. Teoriia, praktyka, innovatsii”, Lviv, Ukraine, 20-21 October 2016, pp. 433 – 435.
- Hashchuk, P.M., Nikipchuk, S.V. and Bohachyk, Yu.O. (1998), “Naturno-mashynni zasoby v modeliuvanni termodynamichnykh protsesiv, shcho perebihaiut u dvyhunakh vnutrishnoho zghoriannia”, Visnyk Derzhavnoho universytetu „Lvivska politekhnika”: dynamika, mitsnist ta proektuvannia mashyn i pryladiv, no. 354, Lviv, Ukraine, pp. 3—9.
- Hashchuk, P.M. and Nikipchuk, S.V. (2017), “Modelno-symuliatsiina tekhnolohiia doslidzhennia termodynamichnykh protsesiv u dvyhunakh vnutrishnoho zghoriannia”, Tezy dopovidei 13 mizhnarodnogo sympoziumu ukrainskykh inzheneriv-mekhanikiv, Lviv, 18-19 may 2017, pp. 93-95.
- Wiebe, I.I. (1970), Brennverlauf und Kreisprozess von Verbrennungsmotoren [Burning process and cycle of internal combustion engines], VEB-Verlag Technik, Berlin, Germany.
- Sharoglazov, B.A., Farafontov, M.F. and Klement'ev, V.V. (2004), Dvigateli vnutrennego sgoraniya: teoriya, modelirovanie i raschet protsessov [Internal combustion engines: theory, modeling and calculation of processes], YuUrGU, Chelyabinsk, Russia.
- Hashchuk, P.M. (2004), Enerhiia ta uporiadkovanyi rukh [Energy and orderly movement], Ukrainski tekhnolohii, Lviv, Ukraine.
- Pattas, K. and Haefner, G. (1973), “Stickoxidbildung bei der ottomotorischen Verbrennung”, MTZ 34, No. 12, pp. 397—404.
- Huber, E., Schey, W. and Vogt, R. (1978), “Beitrag zur Berechnung der Stickoxidbildung im Dieselmotor”, MTZ 39, No 5, pp. 235—237.
Downloads
Published
2018-05-01
How to Cite
[1]
P. M. Hashchuk and S. V. Nikipchuk, “Heating (thermogenesis) in rapid internal combustion engine”, Mech. Adv. Technol., no. 1(82), pp. 92–99, May 2018.
Issue
Section
Original study
License
Copyright (c) 2020 Mechanics and Advanced Technologies
This work is licensed under a Creative Commons Attribution 4.0 International License.
The ownership of copyright remains with the Authors.
Authors may use their own material in other publications provided that the Journal is acknowledged as the original place of publication and National Technical University of Ukraine “Igor Sikorsky Kyiv Polytechnic Institute” as the Publisher.
Authors who publish with this journal agree to the following terms:
- Authors retain copyright and grant the journal right of first publication with the work simultaneously licensed under CC BY 4.0 that allows others to share the work with an acknowledgement of the work's authorship and initial publication in this journal.
- Authors are able to enter into separate, additional contractual arrangements for the non-exclusive distribution of the journal's published version of the work (e.g., post it to an institutional repository or publish it in a book), with an acknowledgement of its initial publication in this journal.
- Authors are permitted and encouraged to post their work online (e.g., in institutional repositories or on their website) prior to and during the submission process, as it can lead to productive exchanges, as well as earlier and greater citation of published work
