Investigation of shape stability of semi-finished samples in the form of a ring made of plastic ceramic material based on SiC, obtained by injection molding

Authors

  • Tetiana Psiarnetska Institute of Superconfirmed Materials named after VM Bakulya, National Academy of Sciences of Ukraine, Kyiv, Ukraine, Ukraine
  • Maksym Tsysar Institute of Superconfirmed Materials named after VM Bakulya, National Academy of Sciences of Ukraine, Kyiv, Ukraine, Ukraine https://orcid.org/0000-0002-4494-9109
  • Oleksandr Lyeshchuk Institute of Superconfirmed Materials named after VM Bakulya, National Academy of Sciences of Ukraine, Kyiv, Ukraine, Ukraine

DOI:

https://doi.org/10.20535/2521-1943.2021.5.1.233134

Keywords:

form stability; compression; injection molding; compressive strength; ceramic material

Abstract

The concept of form stability is considered. A semifinished product in the form of a ring from a thermoplastic mass based on SiC powder has been made on the installation for injection molding developed at the Bakul Institute for Superhard Materials of the National Academy of Sciences of Ukraine  in accordance with the established technological parameters optimized by the results of computer modeling. Schemes of loading and dividing the ring into samples in the form of prismatic segments are presented. A technique for the preparation of experimental samples is proposed. The study of the compressive strength of the samples from the injected semi-finished product has been carried out on the FP-5 mechanical test machine and a corresponding здще of its change has been constructed. The formation of a barrel shape during compression tests of samples, both along the radial and tangential directions, has been established. The values of the minimum and maximum loads at which the samples are destroyed have been determined. An increase in the compaction of the thermoplastic mass around the injection point has been experimentally proved. The scheme and the actual image of crack distribution as a result of destruction of samples have been presented. It is shown that the failure occurs in the area of the presence of the calculated parting lines, which have become stress concentrators.

References

  1. V.V. Bilovol, “Mould filling simulations during powder injection moulding”, Ph. D. Thesis, The Netherlands, Delft Univ. Thechnol., 2003.
  2. V. Novikov, V.V. Ivzhenko, A.A. Leshchuk et al., “Eksperimental'nye issledovaniya i modelirovanie inzhektsionnogo lit'ya izdelii slozhnykh form iz tekhnicheskoi keramiki”, Sverkhtv. Materialy, No. 5, pp. 3–19, 2004.
  3. N.V. Novikov, V.V. Ivzhenko, V.A. Popov et al., “Oborudovanie dlya inzhektsionnogo lit'ya termoplastichnykh mass na osnove keramicheskikh i keramikometallicheskikh poroshkov”, Poroshk. Metallurgiya, No. 9/10, pp. 115–123, 2004.
  4. O.G. Frolova, L.N. Tkachenko, A.L. Maksimenko et al., “Doslіdzhennya techії shlіkeru pri komp’yuternomu modelyuvannі tekhnologії іnzhektsіinogo formuvannya”, Matematicheskie modeli i vychislitel'nyi eksperiment v materialovedenii, No. 9, pp. 228–234, 2007.
  5. O.G. Frolova, L.N. Tkachenko, O.O. Leshchuk et al., “Modelyuvannya zapovnennya shlіkerom єmnostei skladnoї formi”, Matematicheskie modeli i vychislitel'nyi eksperiment v materialovedenii, No. 10, pp. 65–71, 2008.
  6. V.A. Titov, “Problemy kharakteristiki formoustoichivosti i konkurentnosposobnosti shveinykh izdelii”, INNOVATSII, No. 2 (89), pp.120–121, 2006.
  7. T.O. Psyarnets'ka, O.G. Kіrkova, O.O. Leshchuk et al., “Rozrobka tekhnologії іnzhektsіinogo littya keramіchnikh virobіv z vikoristannyam komp’yuternogo modelyuvannya”, Poroshkova metalurgіya, No. 3/4, pp. 28–46, 2021.
  8. DSTU 7809:2015, “Prokat sortovii, kalіbrovanii іz spetsіal'nim obroblennyam poverkhnі z vugletsevoi yakіsnoi kon-struktsіinoї stalі. Zagal'nі tekhnіchnі vimogi”.
  9. DSTU 8429:2015, “Prokat іz resorno-pruzhinnoї vugletsevoi ta legovanoi stalі. Tekhnіchnі umovi”.
  10. GOST 5009-82, “Shkurka shlіfuval'na paperova vodostіika. Tekhnіchnі umovi”.
  11. GOST 27034-86 (ISO 4506-79), “Splavy tverdye spechennye. Metod opredeleniya predela prochnosti i predela tekuchesti pri szhatii”.

Downloads

Published

2021-06-23

How to Cite

[1]
T. Psiarnetska, M. Tsysar, and O. Lyeshchuk, “Investigation of shape stability of semi-finished samples in the form of a ring made of plastic ceramic material based on SiC, obtained by injection molding”, Mech. Adv. Technol., vol. 5, no. 1, pp. 64–69, Jun. 2021.

Issue

Vol. 5 No. 1 (2021)

Section

Mechanics

License

Copyright (c) 2021 Тетяна Псярнецька, Максим Цисар, Олександр Лєщук

Creative Commons License

This work is licensed under a Creative Commons Attribution 4.0 International License.

The ownership of copyright remains with the Authors.
 
Authors may use their own material in other publications provided that the Journal is acknowledged as the original place of publication and National Technical University of Ukraine “Igor Sikorsky Kyiv Polytechnic Institute” as the Publisher.

Authors who publish with this journal agree to the following terms:

  1. Authors retain copyright and grant the journal right of first publication with the work simultaneously licensed under CC BY 4.0 that allows others to share the work with an acknowledgement of the work's authorship and initial publication in this journal.

  2. Authors are able to enter into separate, additional contractual arrangements for the non-exclusive distribution of the journal's published version of the work (e.g., post it to an institutional repository or publish it in a book), with an acknowledgement of its initial publication in this journal.

  3. Authors are permitted and encouraged to post their work online (e.g., in institutional repositories or on their website) prior to and during the submission process, as it can lead to productive exchanges, as well as earlier and greater citation of published work